Send command

Forum Home › Forums › Understanding the Software › Using Formulas › Send command

Tagged: 

Viewing 13 posts - 31 through 43 (of 43 total)
1 2 3
  • Author
    Posts
  • March 11, 2021 at 2:24 pm #8490
    Mikhail
    Moderator

    OK

    May 20, 2021 at 3:13 am #8971
    hethongscada62
    Participant

    Dear Mr.Mikhail,
    Related to this topic” Send command” , can i ask You a question:
    Will 2 relays be controlled via only 1 Button?.
    That’s mean can the command send 1 value to more than 2 input when the Button clicks?
    Thanks and best regards
    Han Hoang

    May 20, 2021 at 12:55 pm #8973
    Mikhail
    Moderator

    Hello,

    You need Automatic Control Module to send 2 commands by 1 click.
    You send the 1st command as usual. A command trigger reacts on the 1st command and sends the 2nd command.

    May 20, 2021 at 12:56 pm #8974
    Mikhail
    Moderator

    Do you mean that 2 relays are 2 different devices?

    May 21, 2021 at 6:02 am #8979
    hethongscada62
    Participant

    Dear Mr.Mikhail,
    – The Automatic Control module is using on my project now.
    – Yes, the 2 relays are 2 different devices. That’s mean only 1 Button can turn On or Off 2 devices at one.
    So how to configure the Automatic Control module?
    Thanks

    May 21, 2021 at 1:10 pm #8984
    Mikhail
    Moderator

    Hello,

    So how to configure the Automatic Control module?

    You should add a new trigger of the command type that reacts on the 1st command. Then add a 2nd command below the created trigger.

    December 28, 2021 at 5:20 pm #9834
    gabeirinhas
    Participant

    Good afternoon, is there any way to send a command from the telegram chat, to activate a signal?

    I am able to send notifications with a trigger but I wanted to know if it is possible to send commands in the opposite direction.

    Thank you.

    December 29, 2021 at 1:59 pm #9835
    Mikhail
    Moderator

    Hello,
    Currently, the Telegram driver doesn’t support receiving commands. It is a good idea for the future improvements.

    December 29, 2021 at 3:41 pm #9836
    gabeirinhas
    Participant

    thanks

    December 4, 2022 at 2:57 am #11717
    SGG
    Participant

    Hello,
    If the time duration to poll a device is 5seconds, and I send a command, rapid scada waits till the device is polled before executing that command.

    Is it possible for rapid scada to suspend/cancel the polling, execute the command then continue/restart the device polling?

    Regards.

    December 4, 2022 at 8:30 am #11718
    manjey73
    Participant

    The command is sent immediately, there is a checkbox in the survey settings for polling immediately after the command

    December 5, 2022 at 8:53 am #11721
    Mikhail
    Moderator

    Hello,

    If the time duration to poll a device is 5seconds

    Request timeout cannot be interrupted. Use smaller timeout if needed.

    December 5, 2022 at 10:09 am #11724
    SGG
    Participant

    Thanks Mikhail, I will use shorter timeouts…thanks also to Manjey.

  • Author
    Posts
Viewing 13 posts - 31 through 43 (of 43 total)
1 2 3
  • You must be logged in to reply to this topic.