Forum Replies Created
-
Posts
-
Dear Mr.Mikhail,
Yes I was tried to send. You can see screenshot bellow:
https://ibb.co/Fs7kSFH
https://ibb.co/PgLKb0r
SMS can not send.
Where is wrong?
Thanks a lot
Han HoangDear Mr.Mikhail and All.
The Module SIM808 (GSM/GPRS/GPS/BLE Module) is testing now.
https://ibb.co/tQvb70M
You can see a screenshot bellow:
It is not working, it is?
Could You let me know?
Thanks and best regards
Han HoangDear Mr.Mikhail.
Yes, I see the driver KpSms.dll that supports both types SMS command and AT command set for sending SMS, but I did not see a custom AT command text example likes the Sending SMS command text examples:
group_name;message
contact_name;message
phone_number;message
Could let me know a text examples when using custom AT command?
Thanks and best regards
Han HoangDear Mr.Mikhail and All,
Rapid scada can use a Module SIM808 (GSM/GPRS/GPS/BLE Module) for sending SMS?
Thanks and best regards
Han HoangDear Mr.Mikhail,
Thank You for your reply.
Camera in my project now is using WiFi Yoosee. The VLC media player can show via link rtsp://admin:Ha50552337!$$!@192.168.2.72:554/onvif1. The Property URL of frame were configured with above link rtsp. But here was not thing in the frame.
Could You advise me how to do?
Thanks and best regardsHi haitan981,
Try to “Clear the browsing data of Chrome”. It maybe can help you to solve that problem.Dear Mr.Mikhail,
– The Automatic Control module is using on my project now.
– Yes, the 2 relays are 2 different devices. That’s mean only 1 Button can turn On or Off 2 devices at one.
So how to configure the Automatic Control module?
ThanksDear Mr.Mikhail,
Related to this topic” Send command” , can i ask You a question:
Will 2 relays be controlled via only 1 Button?.
That’s mean can the command send 1 value to more than 2 input when the Button clicks?
Thanks and best regards
Han HoangSorry.
This is screenshot is true.
https://ibb.co/dfkqg5H
Thank You againDear Mr.Mikhail,
My Rapid Scada project is running well now. It can control my devices via RF transmitter.
For the current moment I don’t understand how Rapid SCADA should behave according your task.
It is sample. Rapid scada can control devices via Outs as relay. This relay control the Input of RF transmitter. That’s all. You can see my screenshot. Rapid Scada can control all devices at my home. Rapid Scada is great.
https://ibb.co/nD4XfgR
There is bad that have to use many relays.
Thank You for your attention.
Han HoangDear Mr.Mikhail,
The sending a static predefined sequence of bytes when a button in Rapid SCADA is clicked have been worked, but not response from device. I think there was the problem with PulseLength. Have to create something likes as a driver or formula?
Thanks a lotDear Mr.Mikhail,
The diagram of the system is sample: replacing a Buttons on RF(or IR) remote controller (garage door, lights, fan,…) by Buttons on Web rapid scada .
For example: The EV1527 chipset in garage door remote uses a 24-bit codeword comprising 20 address bits followed by 4 data bits. The codes have been got from garage door remote are:
Button 1:
Decimal: 8571080 (24Bit)
Binary: 100000101100100011001000
Tri-State: not applicable
PulseLength: 321 microseconds
Protocol: 1
Raw data: 9964,956,332,312,976,312,976,308,980,304,980,308,980,952,340,304,980,956,336,188,908,276,728,264,124,168,308,60,24,60,236,88,88,204,88,76,80,56,1020,284,440,56,24,40,100,84,12,36,56,Button Address Data
Button 1: 10000010110010001100 1000
Button 2: 10000010110010001100 0100
Button 3: 10000010110010001100 0010
Button 4: 10000010110010001100 0001
So can create a driver that sends commands with above data from Rapid Scada directly to RF (or IR) Transmitter part?
ThanksDear Mr.Mikhail,
Yes, the transmitter can be manual available. I am using an Arduino as intermediate driver, so i can control a transmitter via Button on Rapid scada Web to send codes.
But the better is having a driver, ins’t it?
ThanksDear Mr.Mikhail,
Thank you for your reply.
I am not IT developer, so i can not create a driver but i have had a another solution. Are you going to develop it?
ThanksDear Mr.Mikail,
The email driver was testing. It is running in my project. I configured the email device that can send an email only to single contract. That’s mean i can not configure the device that can send email to group_name. I think there is a problem in creating group_name in the command text. Could you let me know How to create a group_name?
Thanks and best regards
Han Hoang
